Відео

THAT IS NOT THE PCV!!! it's part of the pcv system, that motor has 2 pcv valves and that is neither. That doesn't even look like any valve I've seen it looks like a diafram, maybe because it is!

How can i clear a pending P26c8 code on my 2018 buick lacrosse?

Gonna leak again the following week

Sorry thank you too I appreciate it !

What made you change it ? How did you clear the codes ?

Wouldn't it be easier to remove the bed?

Hi where can I buy the oxygen sensor.thank you

An expensive tone generator.

The second I saw you let the caliper dangle by the brake line you lost all your mechanical credibility i wouldn't let ya do my brakes for sure. Buy you some caliper Hangers! They're cheap cheap and will save you a headache of replacing that brake hose when you bust one where they're crimped to the caliper they WILL leak from hanging by it's own weight luckily that car isn't too old. Still good video though and good camera work all in all. Also that green washer is part of the cv axle assembly and is pretty important, it protects the mating surfaces of the axle/bearing preventing burring/friction.

My shocks were so comically bad that they were like the fake RC car shocks that just slide in and out it was hysterical, truck ride like trash too. Put new ones and made me real happy how it is now. Gonna do bushings and ball joints now, bushings aren't looking so hot on all for arms gonna have fun with that.

Good detail video.

Good video, one question is there a gasket you put between the tank and pump?

ACTUALLY! Only a few will understand.

Thanks for the most helpful video!

If it turns on with the paper clip what does that mean

Awesome video resolved my prob quickfast

Sudden onset of crank but no start. No noise from the pump at all upon key-start. Relay checked and fuse 18 both OK. Gotta be the pump, yeah? I’m going to cheat and “cut carpet”. Hey she’s now a project van anyway!

Very helpful! I've had my 2004 Thunderbird since 2016 and just recently decided to start doing my own routine maintenance. After watching this video, the process was much simpler - definitely saved time and made me feel more confident.

Bro thanks for this video, i was thinking about taking my CR-V to a shop and probably pay more than 100 dollars for this simple job.

OMG LOOSE THE KIDS AND WIFE NOISE MAN!!!!

How long will it last ?????? have a 2001 Toyota sienna and I can't afford to fix it properly .....And wers case sen. What else could go wrong ??? 😊

Amazing video. Thank you, this was very helpful.

You didn't say anything about the vortex accelerator or the quantum coupler I'm disappointed sir! 🧐

Great content, very informative on a badass Muscle Car.

I’m thinking about going for it. I’m so use to paying to get minds done 🤦🏻‍♂️

Thank you for the video, Jabo. I didn’t have any information on this sealed transmission but now I do. Appreciate you very much!

This could be related to p0171?

Man thank you!!!

Thank you

What about using the repaired bearings? Is there an extra step or the same process? I was advised to use the repaired bearings on mine. It's a 08 Avalanche.

Dude this guy is seriously gonna get someone to do this wrong. "So forth" Take this down

This video fucking sucks. You are terrible at explaining this.

Nice to see mechanic who is showing basic upkeep

Easy to do

Great video brother. Keep it up Thanks.

The title says EASY it certainly doesn't seem easy to me, it seem like a lot of frustration!!!

Great video thanks!!

Lmao hold that like a blunt 😂

To the point thanks a lot ✌️😊

Do you know if VW trouble codes are recorded by the vehicle ?

Just finished changing mine. Your video helped a lot and was very accurate. Thanks!

How do u bench bleed a master cylinder without taking out the slave?

what if you get no spark from the ignition coil

How long did it take to fully replace it

Wow, seems crazy involved to get to a fuel pump! What is the normal life of one of these?

Doesn't those KYB shocks say they can't work with the OEM springs? It says springs with at least 1" drop. What springs did you use?

That caliper should have a metal clip in the center ? Did you remove it completely ? Is it not needed ?

Very good video thank you sir.

What about the upper oil pan gasket, my 2016 was leaking at first oil change, was done under warranty, now it’s out of warranty at 108k and it’s leaking again

So I did what you did and the thermostat. And it still wants to over heat. Do I now need to do the water/ radiator?